Prep Your Home for Winter With These 15 Low-Cost Tricks

1. Install weatherstripping

Check your home’s exterior doors for cold air leaks. Do this from inside the house. The high-tech approach is to use a laser infrared thermal gun to detect cold drafts. The low-tech way is to move a lit candle around the door frame; the flame will blow toward you when there is a draft.
Seal a drafty door by installing foam or felt weatherstripping inside the door frame. Ask at your hardware store for the correct products and installation instructions.
 

2. Install a door sweep

Use a door sweep to stop drafts from entering your home under an exterior door. A sweep is a flexible piece of rubber or plastic that’s held to the door’s lower edge by a strip of aluminum.
kk
3. Seal attic air leaks
Find and seal gaps that could be allowing as much as 30% of your heated or cooled air to leak outdoors. Pull back attic insulation to find and seal cutouts in drywall for electrical fixtures, pipes, fans and outlets. Also, check wiring, chimneys, flues, vent stacks and ducts, and seal them on the inside. Use caulk to fill smaller gaps and pressurized expanding foam for bigger openings.
 
4. Close the damper
Heated or cooled air flies up the chimney when you leave the fireplace damper open. Make it a habit to shut the flue after the fireplace has cooled.
k
5. Add attic insulation
Insulation keeps warm air inside in the winter and expensively cooled air inside in the summer.
kk
6. Install a programmable thermostat
A programmable thermostat can save up to $180 a year on fuel costs. The thermostat can save fuel by automatically lowering (or raising) your home’s temperature while you’re away. It also keeps temperatures consistent, saving fuel.
 
7. Set the temperature manually — and leave it
You can enjoy fuel savings for free simply by setting your thermostat to one temperature in the morning, another at night and otherwise leaving the thermostat alone. If you’re chilly, put on a sweater and warm socks instead of raising the heat.
 
 

8. Seal furnace ducts
Sealing leaks can reduce the risk of the buildup of dangerous gases. Before you start the job, ask a heating contractor whether you need to have a combustion safety test done first. You won’t be able to reach all the ducts; but you can improve performance by sealing exposed ducts in the attic, crawl space, unfinished basement and garage.
Focus on the places where ducts, vents and registers meet floors, walls and ceilings. Use mastic sealant or metal tape, which are more durable than duct tape, to seal the seams and connections.
k
9. Replace furnace filters monthly
Dirty furnace filters reduce furnace efficiency and push up heating bills. They also shorten the life of a furnace.
Check and replace the furnace filter monthly in winter or every three months while the system is in operation. Your owner’s manual will tell you where it’s located. Hold the filter up to the light: If you can’t see light through it, you need a new one.
Pleated filters work best because they trap more dirt particles.
 
10. Keep your furnace running smoothly
Servicing your furnace regularly helps you catch problems before expensive breakdowns, prolong the furnace’s life and keep it running more efficiently.
Newer furnaces need professional servicing every two years. Older units require annual servicing.
Check your furnace’s manual to see which specific steps are recommended. Ask friends and colleagues for names of good technicians. Find one or two you trust and stick with them.
k
11. Insulate the hot water heater
Save on fuel by wrapping older water heaters in a blanket of insulation, an easy DIY project that even a beginner can do. Your utility company has instructions. When insulating a gas or propane water heater, do not cover the burner access.
Do not insulate:
  • Pre-insulated water heaters. These are newer units with factory-installed insulation of R-16 or better (check the manufacturer’s label) under the metal shell.
  • Water heaters located where the added heat is welcome.
  • Water heaters whose manual or paperwork warns against insulating.
  • Tankless (on-demand) water heaters.
12. Lower the hot water temperature
Hot water heaters typically are set at 140 degrees. Lower the temperature on yours to 120 degrees for fuel savings. You’ll reduce the chance of accidental burns, and the water still will be plenty hot for bathing, washing clothes and doing dishes.
 
13. Plug household leaks
Grab a tube of caulk, a can of spray foam gap-sealer, a pencil and notepad. Tour your home, inside and out, including the basement, to find and fill cracks and gaps in siding, windows and foundation. Note locations of problems you can’t fix right away.
Use caulk for small cracks and the foam sealer for bigger gaps. Inside the home, use a candle flame or digital thermometer to find where cold air is entering. Pay attention to windows, skylights, chimneys, vents and door frames (in areas around the frame not remedied by tip No. 1’s weatherstripping).
Also, check openings around appliance vents, electrical and plumbing fixtures and furnace ducts and check the top of basement walls where the foundation meets wood.
 
14. Insulate hot water pipes
Insulate the hot water pipes in your basement or crawl space by snapping foam sleeves on them. You’ll find pre-slit, hollow-core, flexible foam pipe insulation at hardware stores. Make a note of your pipes’ diameters and lengths, and bring the measurements when you shop.
Exposed pipes waste heat by cooling the water as it runs through them. Be sure to include pipes between the hot water tank and wall. Also, insulate cold water pipes for the first 3 feet after they enter the house.
 
15. Use your window coverings
It’s surprising how much insulation can be provided by curtains, drapes, shades and even mini blinds. Draw window coverings at night and when you’re away to conserve heat in the home. In hot weather, draw window coverings in the morning to keep the house cool, saving money on air conditioning.

by Marilyn Lewis from Money Talks News